whatisstill.blogg.se - Apc back ups 650 powerchute software download

APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD SOFTWARE
APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD MAC
APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD WINDOWS

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port on your computer. See the documentation provided with your computer.

APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD MAC

If you are using a Mac OSX, use the native shutdown feature to protect your system.

APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD WINDOWS

Note: PowerChute is only compatible with a Windows operating system. Monitor the UPS for power usage and power events. When power is restored, it will restart the computer.Ĭonfigure the UPS to use features such as power-saving outlets, shutdown configuration, and alarms. During a power outage, PowerChute will save any open files on your computer and safely shut it down. Protect your computer and other equipment during a power outage.

APC BACK UPS 650 POWERCHUTE SOFTWARE DOWNLOAD SOFTWARE

Use PowerChute Personal Edition software to configure the UPS settings. PowerChute ® Personal Edition Software Overview The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from power surges when connected through the Back-UPS coaxial connectors. Surge protection outlets provide protection from power surges or spikes.Ĭonnect a printer, scanner or other peripheral devices that do not need to remain on during power outages, or utility problems to the surge protection outlets. Surge protection outlets provide protection to connected equipment when the Back-UPS is connected to utility power, and is switched on or off. Connect a computer, monitor and other peripheral devices to the outlets. To order replacement battery cartridges contact APC.īu202a Battery Backup + Surge Protection Outletsīattery backup outlets provide protection to connected equipment when the Back-UPS is turned on and connected to utility power.īattery backup outlets receive power from the Back-UPS for a limited period of time when a power outage, or brownout condition occurs.īattery backup outlets provide protection from power surges or spikes. Use only approved APC replacement battery cartridges.ĭeliver used batteries to a battery replacement facility in the packaging provided by APC with the replacement battery cartridge.

Allow 5/16" (8 mm), of the screw to protrude from the wall.

Vertical installation, use 2 screws 5.4" (137.2 mm) apart.

Horizontal installation, use 2 screws 7.3" (186.3 mm) apart.

Be sure that the release tab locks into place. Release tab located on the rear side of the It is normal for small sparks to be seen when the battery cable is connected to the battery terminal.Ĭonnect the battery cable securely to the Prior to connecting any equipment to the unit, connect the battery cable to the unused battery terminal. Remove the “Stop! Connect the Battery” label that covers the outlets. The Back-UPS is shipped with one battery cable disconnected. Interference received, including interference that may cause undesired May not cause harmful interference, and (2) This device must accept any

See the Troubleshooting section for additional assistance.Operation is subject to the following two conditions: (1) This device

Wiring presents a shock hazard that should Operation a battery power supplied outletĮxhausted and the UPS is waiting for utility The battery is in need of charging, or is at Power to the load connected to the Batteryīattery power to the load connected to the Use the following table to identify the status of the Back-UPS ES.

The Back-UPS ES indicates operating status using a combination of visual and audible indicators. The UPS also protects a cable modem, CATV converter, or DSS receiver from surges when it is connected through the UPS coaxial connectors as shown in the drawing below. The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line - DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, 10/100 Base-T Ethernet, or fax machines from surges when connected through the UPS as shown in the drawing below. The software will automatically find the computer’s USB Port.Ĭonnect Modem / Phone / DSL / Fax / 10/100Base-T / HPNA / Cable Modem / CATV or DSS to Surge Protection Connect the other end of the cable to the USB port on your computer. The supplied cable and software provide automatic file saving and shutdown of the operating system in the case of a sustained power outage.Ĭonnect the cable to the Data Port of the Back-UPS ES. Plug the Back-UPS ES power cord directly into a wall outlet not into a surge protector or power strip. Direct sunlight - Excessive heat - Excessive humidity or contact with fluids